December 05, 2024, 05:39:40 am
Welcome, Guest. Please login or register
News:

Arturia Forums



Author Topic: Laboratory - Bad Pot. Cleanable?  (Read 6999 times)

JDoo

  • Beta-testers
  • Full Member
  • *
  • Posts: 130
  • Karma: 3
Laboratory - Bad Pot. Cleanable?
« on: December 30, 2018, 09:26:14 pm »
I have a years-old Analog Experience The Laboratory 61.  The 'Cutoff' knob/control has ceased working.  If I move it around some... I can see controls in whatever GUI I happen to be using, slightly move - but that's all.  I have mapped cutoff to another knob, but wanted to know if anyone has opened their Laboratory, and attempted to clean pots/etc?  Specifically.. if there are any bits that I should be careful about (like tight ribbon controllers, etc..  Or - even, "Don't do that.  I tried, and wrecked my controller".  :D    Like I said, I have mapped Cutoff to another parameter so it's not critical .

Thanks for any help (or pointer to where a manual for the "61-key universal keyboard controller" that Arturia uses for this, may be picked up?)

Joe

JDoo

  • Beta-testers
  • Full Member
  • *
  • Posts: 130
  • Karma: 3
Re: Laboratory - Bad Pot. Cleanable?
« Reply #1 on: January 10, 2019, 09:27:46 pm »
This thread is going to die here, isn't it?   ;D   

If I ever get around to pulling my "The Laboratory" apart -- I'll take pics and share.  In the meantime --- if anyone has an idea where I could download a manual that talks about the hardware... that would be wonderful.

Cheers -

Joe

MajorFubar

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1.176
  • Karma: 67
Re: Laboratory - Bad Pot. Cleanable?
« Reply #2 on: January 10, 2019, 09:46:36 pm »
I haven't opened this controller specifically, but I've cleaned many a potentiometer in my time and lived to tell the tale.

It will usually be obvious when you take the back off what you're up against. Be wary that the pots might be nutted from the front, pull the knobs off first just to check. They aren't nutted from the front on the KeyLabs, but they might be on this. Disassembly will be a case of carefully removing any ribbon cables connecting the circuit board to the keybed etc and unscrewing a few screws. Whatever you do don't use WD40 as a cleaner though. Use Servisol Switch Cleaner, or similar. Everyone seems to think WD40 is for fixing electrical maladies but it's not, it's a Water Dispersant (clue is in the name) and in fact it purposefully leaves behind a non-conducting layer as it dries.
2022 Apple Studio Max 32/32/2TB Monterey • V Collection 9 • Analog Lab 4 + 5 • KeyLab 88 • KeyStep

JDoo

  • Beta-testers
  • Full Member
  • *
  • Posts: 130
  • Karma: 3
Re: Laboratory - Bad Pot. Cleanable?
« Reply #3 on: January 11, 2019, 09:26:19 pm »
Thank you!!  This will help tremendously.

Joe

I haven't opened this controller specifically, but I've cleaned many a potentiometer in my time and lived to tell the tale.

It will usually be obvious when you take the back off what you're up against. Be wary that the pots might be nutted from the front, pull the knobs off first just to check. They aren't nutted from the front on the KeyLabs, but they might be on this. Disassembly will be a case of carefully removing any ribbon cables connecting the circuit board to the keybed etc and unscrewing a few screws. Whatever you do don't use WD40 as a cleaner though. Use Servisol Switch Cleaner, or similar. Everyone seems to think WD40 is for fixing electrical maladies but it's not, it's a Water Dispersant (clue is in the name) and in fact it purposefully leaves behind a non-conducting layer as it dries.

MajorFubar

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1.176
  • Karma: 67
Re: Laboratory - Bad Pot. Cleanable?
« Reply #4 on: January 11, 2019, 09:27:07 pm »
No worries Joe, glad it was of some help.
2022 Apple Studio Max 32/32/2TB Monterey • V Collection 9 • Analog Lab 4 + 5 • KeyLab 88 • KeyStep

JDoo

  • Beta-testers
  • Full Member
  • *
  • Posts: 130
  • Karma: 3
Re: Laboratory - Bad Pot. Cleanable?
« Reply #5 on: January 28, 2019, 09:36:49 pm »
Update -

I was all set to pull my The Laboratory apart... but something caught my eye, while I was using Analog Lab 3.  I was using a saved controller configuration. A couple of years ago, I occasionally get a high pitched whine,  based on cutoff settings or moving the cutoff knob.  So, I had remapped it to another knob. 

So earlier today, I reset Analog Lab to a default Laboratory controller configuration, and got my Filter Cutoff knob working again.  Problem solved.  No whine either?   Posting this here, in case someone stumbles into the same issue.  First thing to check is that you haven't mapped a control somewhere else.  ::)

Joe

 

Carbonate design by Bloc
SMF 2.0.17 | SMF © 2019, Simple Machines