November 07, 2024, 01:42:48 pm
Welcome, Guest. Please login or register
News:

Arturia Forums



Author Topic: Set sequencer start and end point  (Read 5243 times)

tp

  • Apprentice
  • Apprentice
  • *
  • Posts: 24
  • Karma: 3
Set sequencer start and end point
« on: July 24, 2017, 06:08:22 pm »
Currently you can only set the Sequencer end point, by pressing the Seq Length button and the corresponding step while in sequencer mode. It would be great if you could set both the end and begin point by pressing on two separate steps (simultaneously or one after the other) while holding down the Seq Length button. This would allow you to use a long sequence as a reservoir of many shorter subsections which can be activated in performance in a flexible manner, making the sequencer much more powerful and expressive.

joeman

  • Apprentice
  • Jr. Member
  • *
  • Posts: 52
  • Karma: 2
    • Musical Experiments
Re: Set sequencer start and end point
« Reply #1 on: July 25, 2017, 02:32:59 am »
Good idea. Agreed.
Experiencing a flow of temporal information now, and in anticipation, and in retrospect.

SomeCallMeFamous

  • Jr. Member
  • **
  • Posts: 56
  • Karma: 3
  • Sound Designer, Record Producer, Live Performer
Re: Set sequencer start and end point
« Reply #2 on: October 23, 2017, 11:31:45 pm »
Would be a great add on
''Put Signature Here''

madScientist

  • Apprentice
  • Apprentice
  • *
  • Posts: 5
  • Karma: 0
Re: Set sequencer start and end point
« Reply #3 on: October 24, 2017, 10:25:55 am »
totally aggree. When I first played arround with the sequenzer, I Intuitively searched the start point.
This would be another dimension. 64 steps are quite a lot for more than one sequenze.

Brutefactor

  • Apprentice
  • *
  • Posts: 19
  • Karma: 4
Re: Set sequencer start and end point
« Reply #4 on: August 09, 2020, 04:10:42 am »
Agree, this is easy to implement and very useful.
Start and end point could be set by "double pressing" or "shift pressing" a step (using some button as shift - like the Seq-button). Best if one hand can be used. Some logic must be defined to decide if a press on one of the steps between start and end means "set new start" or "set new end".
Could be done by using the sequencer knobs "<" and ">" as shift keys. Hold "<" and press a step = new start, Hold ">" and press a step = new end. Minimal change, great value!

STM

  • Apprentice
  • *
  • Posts: 49
  • Karma: 1
Re: Set sequencer start and end point
« Reply #5 on: August 09, 2020, 08:21:11 am »
Very good idea!
Beeing able to change start and end single handed would be a bonus.

DrJustice

  • Super Doc
  • Administrator
  • Hero Member
  • *****
  • Posts: 1.046
  • Karma: 480
Re: Set sequencer start and end point
« Reply #6 on: August 10, 2020, 02:40:50 pm »
...Could be done by using the sequencer knobs "<" and ">" as shift keys. Hold "<" and press a step = new start, Hold ">" and press a step = new end. Minimal change, great value!
I like that.

A single handed version could be done with something like pressing (e.g.[1]) "Sequencer" + "<" or ">", blinking the Sequencer button, then the next press on a step button would set the start or end. There could also be a time out whereby the Sequencer button stops blinking to indicate that. Both your immediate action and the delayed (single handed) action could even exist together with no conflict.


[1] - The most logical button chording for setting the end, "SEQ Length" + ">", is taken by Extend & Duplicate, so we need another button, and for a timeout one with a LED would be good. Perhaps "Patterns" or "Link" would be better since you don't stand the chance of accidentally stopping the sequencer by using those.

mylorman

  • Apprentice
  • *
  • Posts: 23
  • Karma: 0
Re: Set sequencer start and end point
« Reply #7 on: November 20, 2020, 07:05:07 am »
yes this would be a very useful feature .. especially for live performance

Germano

  • Apprentice
  • Apprentice
  • *
  • Posts: 16
  • Karma: 0
Re: Set sequencer start and end point
« Reply #8 on: December 01, 2020, 07:57:42 pm »
+1

 

Carbonate design by Bloc
SMF 2.0.17 | SMF © 2019, Simple Machines