Arturia Forums
Hardware Sequencers => BeatStep Pro => BeatStep Pro - Technical Issues => Topic started by: tallgeese on August 09, 2015, 06:45:10 am
-
I created a custom control map using undefined CC#20 - CC#31 using USB&MIDI for knobs 1-6 and 9-14 respectively. I attempted to perform midi learn on Addictive Drums, Rapture Pro, and Z3ta, but discovered BeatStep Pro Fw. v1.1.1.6 isn't sending CC messages.
-
Hi
I am having almost the same problem
But for me its sending cc's in control mode in stand alone mode with a arturia mini v2
but inside my daw BitWig studio it wont allow midi learn to the vst
but it will allow cc's to midi learn the daw controls
my old beatstep 1 works perfectly in everything
so something strange is going on with control mode in the BSP
cheers
kev
-
Come on somebody must have the answer ?
cheers
kev
-
The Arturia MCC is a little obtuse (IMO) and buggy.
Setting MIDI CC on the BS Pro does work. I'll post the steps I used that work ASAP.
There is a bug in the MCC GUI. After the BS Pro is synced with the MCC, turning a knob may highlight the subsequent numbered step buttons; just a visual bug, not an operational problem.
-
Hi all . In the mcc control panel make sure you set each control midi ports to midi &usb and midi channel to user otherwise the controls will not work on your daw.
theres a new mcc and FW coming
regards
terrym
-
Hi Mr T
I have set this in the MCC if it was not correct
then it wouldn't work in stand alone but it does
and in Bitwig if I midi learn any of the controls IE faders on the mixer
as soon as I turn a knob on the BSP it works
its just when I use Miniv 2 as a vst and selct midi learn and turn a knob on the BSP it does NOT work
but again if I select any other feature of BitWig and turn a knob it DOES work
its as if there is something blocking the CC's from getting through to the vst
so I thought may be this is a Bitwig problem
but it cant be Bitwig because if I choose my old BS 1 as the input everything works
anything else you think I could be doing wrong ??
cheers
the pain in Spain
Kev
-
Hi Mr T
if you want to see exactly what I mean
you can take over my Pc with teamviewer and see for yourself
let me know if your willing to take a look
cheers
kev
-
Im afraid my time is short so i don't have time to sync up but i will look at this tonight .
regards
Terrym
-
Also open the mcc while connected in bitwig open midi console at the top press sync and in control mode turn a few knobs are they showing up in the midi console?
-
Hi
you cant open the MCC while Bitwig is running ?
you cant sync the BSP
message is the device is connected but not synchronized
all I get in the midi console is OUT F0 7E 7F 06 01 F7 SYSEX
repeated over and over
but without Bitwig running when I turn some knobs I get decay time, chorus send,brightness etc etc
One other strange thing i'v just noticed
the BSP cc's work on the Bitwig stuff in midi learn but not the vst
but the old BS 1 works in control mode on the vst but NOT on the Bitwig stuff
cheers
kev
-
Did you put the BS Pro in Control Mode and create a new MIDI CC mapping?
-
HI all
After getting a reply from the Boyz at BitWig
this problem for me is now sorted
it turns out it was the script that I was using wasn't routing
the cc's properly
so I will have to put up a request for a better script
unless Arturi is going to supply one
cheers
kev
-
Hey turbo_kev,
Can you tell in more detail where my controller script "wasn't routing the cc's properly"?
So I can fix it in the script.
Thank you!
-
Hey turbo_kev,
Can you tell in more detail where my controller script "wasn't routing the cc's properly"?
So I can fix it in the script.
Thank you!
HI I will try my best so that you can understand the problem I am having
1. To make it simple I will use 1 vst Arturia miniV2
2. use my BSP to control the track with the miniV 2
3. select from the drop down menu your script channel 1
4. start bitwig and the sequence plays OK
5. now while the sequence is playing put the BSP in CONTROL MODE
6. put the miniv2 in to midi learn mode
7. click a knob on the miniv2
8. turn a knob on the BSP and NOTHING happens
9. right click on any BitWig fader or knob
10 turn a knob on the BSP and it works
so it seems to me that something is blocking the cc's getting through to the vst
but allowing them through to BitWig controls
If I use TOMS multi script everything works perfectly ?
Another strange thing is. With TOMS script I don't have to add a generic midi clock transmitter
but with your script Sometimes at random times the BSP will NOT start when I press
play on BitWig so I end up having to add a generic midi clock
the above happens at random times so I can't see what might be causing this
sorry to be a pain
I am Not a musician in any shape or form
I just love the sound of old analog synths
and spend many hours TRYING to sound like tangerine dream
without much success. But hey I have a lot of fun
cheers
Kev
-
Hi Kev,
thanks for the input. I just solved the CC/MIDI-learn problem, hope it works fine for you now..
The latest version is here:
https://github.com/justlep/bitwig
As for the Play/Stop issue, I haven't encountered it yet (at least not that I remember at the moment), but I'll keep an eye on it and see if it's a problem of the script.
Cheers ~
Lennart